Skip to main content

Products

Nio

How to turn Nio on/off

Sudio Nio will automatically turn on when you lift out the earbuds of the charging case, and it will turn off when you put them back in the case. You can also turn them off by pressing the touch button for 6 seconds until you hear "power off”.
In order to turn them on, put them back in the charging case and simply take them out of the charging case.

How to use the touch controls on Nio

You can follow these instructions for using the touch controls on Sudio Nio:

Control music
One touch(L/R): Pause and start music
Double touch on the right side: Jump to the next song
Double touch on the left side: Back to the previous song
Triple touch on the right side: Turn up the volume
Triple touch on the left side: Turn down the volume

Phone calls
One touch (L/R): Receive or End a phone call
Press and hold for 2 seconds(L/R): Reject a phone call

Turn on/off the earbuds
Press and hold for 6 seconds (right or left): Turn off
Press and hold for 3 seconds (right or left): Turn on

How to pair Nio with a device

Follow the steps below to pair your Sudio Nio with your device:

  1. Turn on the wireless connection in your device's settings.
  2. Lift both earbuds from the charging case.
  3. Sudio Nio will automatically be in pairing mode. Click “Sudio Nio” in your device list to connect.
  4. Now your Sudio Nio is paired with your device and you can start to enjoy music!

If you would like to use only one of the earbuds, you can do so by just taking out the one you want to use from the charging case.

What to do when sound is only coming out from one earbud

If your earbuds say “pairing successful” but you can only hear sounds from one side, this indicates that the earbuds are no longer paired together. In order to pair them again, please put back both earphones in the charging case, wait for 5 to 10 seconds and lift both at the same time. If this does not work, proceed with a factory reset

What to do when Nio is behaving unexpectedly or not pairing

If your Sudio Nio is behaving unexpectedly or you are having difficulty pairing, please check first if there are any HC articles related to your issue. If you can't find a troubleshooting article that may solve your case, please follow the factory reset steps below.

Factory reset instructions:

    1. Turn off the wireless connection on your device.
    2. Put both earbuds in the charging case and make sure to close the case.
    3. Forget “Sudio Nio” in the wireless connection list on your device. Sudio Nio should no longer be synced to your device. If you have connected Sudio Nio to multiple devices, forget them from all other devices as well.
    4. You can see the button on the bottom of the charging case. Press and hold the button for 3 seconds.
    5. Turn on the wireless connection on your device and select “Sudio Nio” in the list to pair it with your device.

How to manage multiple devices

Sudio Nio can remember up to eight paired devices, which means that you don't have to follow the pairing step every time you switch between devices. When Sudio Nio is turned on, it will automatically connect to the device most recently connected.

If you want to reconnect to one of your previously paired devices, please disconnect Sudio Nio first from the device you are currently using, and click "Sudio Nio" in the list of the next device you want to connect.

Sudio Nio supports multi-pairing, but you can only play audio from one device at a time. (Multi-point connection is not supported.)

Ett

How to turn Ett on/off

Ett will automatically turn on when you lift out the earbuds of the charging case, and it will turn off when you put them back in the case.

You can also turn them off by pressing the buttons for 6 seconds until you will hear "power off". In order to turn them on, you need to put them back in the charging case and take them out.

How to use the button controls on Ett

By clicking the button on either side of your Ett, you can control various features.

Music
One click: Pause and play music
Two clicks: Jump to the next song
Three clicks: Go back to the previous song

Phone calls
One click: Receive/end a phone call
Press and hold for 2 seconds: Reject a phone call

Turn on/off the earbuds
Press and hold for 6 seconds: Turn off
You can only turn them off by pressing the button for 6 seconds.
In order to turn them on, put Ett back in the charging case and take it out.

Turn on/off active noice cancelling (ANC)
Press and hold for 2 seconds

How to take phone calls with Ett

If you would like to receive/hang up a phone call, please click the button on either side of your Ett once.
If you would like to reject an incoming phone call, please press and hold the button on either side of your Ett for 2 seconds.

How to change the volume

You can change the volume through the device that is connected to Ett.

How to turn Active Noise Cancellation (ANC) on/off

To turn on/off ANC, press and hold the button on either side of the earbuds for 2 seconds.
You will hear "noise cancelling" when ANC is turned on, please note there is no signal sound when you turn ANC off.

Transparency mode on Ett

Ett's transparency mode lets ambient noise through so you can better hear yourself speaking during phone calls.
As soon as your phone recognises that a phone call is incoming, Ett will automatically pause what you are listening and switch to transparency mode, then lets you decide whether to answer the phone call or not.
The transparency mode will be on during the call regardless of use of ANC. When you end the phone call, Ett goes back to normal mode or ANC mode depending on how you were using Ett before the call.

Fem

How to pair Fem with a device

The earbuds are automatically on once they are lifted out from the charging case.

Turn on the wireless connection function in your device's settings. Lift both earphones from the charging case and they will be in pairing mode. Select 'Sudio Fem' in the wireless connection list on your device.

To turn off the earbuds, the earphones will be automatically off once you put them in the charging case. To manually turn earphones off without using the case, simply press for 8-10 seconds until the red light glows.

How to use the touch controls on Fem

Here are our instructions for using the touch controls on Fem:

Music
One click: pause and restart music
Double click on the right side: jump to the next song
Double click on the left side: go back to the previous song
Triple clock on the right side: turn up the volume
Triple click on the left side: turn down the volume

Phone calls
One click (right or left): receive/end a phone call
Press and hold for 2 seconds(right or left): reject phone calls

Voice assistant (Siri and Google Assistant)
Press and hold for 1 second (right or left): activate voice assistant

Turn on/off the earbuds
Press and hold for 6 seconds (right or left): turn on/off the earbuds

What to do when Fem is behaving unexpectedly or not pairing

Sometimes, the earphones fall out of sync. If, for example, both sides say 'pairing' but the sound is only from the right side then this indicates that the earbuds are no longer paired together. In this case, please put back both earphones in the charging case, wait 10 seconds and lift both at the same time. If this does not work, do a factory reset by following the instructions below.

How to do it:

  1. Put both earphones in the charging case.
  2. "Forget" the earphones in your wireless connection settings. Fem should no longer be synced to your device. If you have connected Fem to multiple devices, forget Fem from all the devices.
  3. Lift both earphones from the charging case.
  4. Turn off both earbuds manually by pressing the touch buttons until the red light shines on both.
  5. Press and hold the left earphone button until you see white light flash once --> blink in white and red --> white light flash twice. Repeat the same step for the right earbud.
  6. Put both earphones back in the charging case and wait for at least 10 seconds.
  7. Lift both earphones at the same time from the charging case and they will be in pairing mode. Both will blink separately. When one earbud blinks red and white and the other's light stays dark, that means means they are paired together once again.
  8. Start the wireless connection on your device again. and select "Sudio Fem" in the list.

How to clean Fem

Light colored earphones always need to be treated a bit carefully.

For discolorations, we recommend to gently clean the areas with a damp cloth or with a small amount of water.

Fem's charging case and earbuds are made of special material, do not use alcohol to rub the charging case.

In some cases, being exposed to strong sunlight or high heat might alter the form of the silicone material.

Water resistance rating (IPX5)

Fem is a device with a level 5 water protection rating, which means that the earbuds are water-resistant. At this level, the earbuds can handle exposure to low-pressure water jet spray. IPX is an official rating that is awarded by passing tests that are conducted by a third party. Fem is also completely sweat-proof and can be used during exercise.

However, for an IPX 5 rating, we would like to communicate that there is no guarantee that the earbuds will remain in full operation after activities like swimming or showering with them.
While the earbuds have IPX5 protection, the charging case is not waterproof. If you touch the charging case with wet hands or put earbuds in the charging case while they are not completely dry, the product might be damaged. Unfortunately, if the earphones are damaged in these cases, they will not be considered a manufacturing defect and will not be eligible for replacement through our warranty.

 

Fem - User Manual (PDF)

Tolv

How to change songs on Tolv

If you would like to go forward to the next song, quickly press the button on the right side twice. If you would like to go back to the previous song, quickly press the button on the left side twice.

Sometimes, with some apps, to go back to the previous song, you will need to do it on your phone device.

What to do when Tolv is behaving unexpectedly or not pairing

If the earphones are behaving unexpectedly or you are having difficulty pairing, we recommend a reset. 

Please take your time with this process as there are several steps.

If the earphones fall out of sync, to pair again, you'll first have to bring them to the factory reset:

  1. Turn off both earphones by pressing and holding both buttons for 6 seconds.
  2. Start the earphones again by pressing and holding both sides for 13 seconds, until the lights stop blinking.
  3. Put the earphones back in the case and wait for 10 seconds.
  4. They are now reset.

Then you can start to pair them:

  1. Lift both earphones from the charging case at the same time (do not lift one by one, but both at the same time) and they will be in pairing mode.
  2. Select 'Sudio Tolv' in the wireless connection list on your device.

How to check battery status on Tolv

There are two LED lights on the back of the charging case.

The left LED light indicates the battery level of the case. The right LED light indicates the battery level of the earphones.

When it shows red light on the charging case, the case needs to be charged. When the red light changes to white light the charging case is fully charged. 

Charging the earphones in the charging case:

  • If the left LED light shows white and is ON (stays still without blinking) for 10 seconds, it means the charging case has 70% to 100% of battery, in this case, the charging case can fully charge the earphones 3 to 4 times.
  • If the left LED light shows white and blinks for 10 seconds, it means the charging case has a 40% to 70% battery, in this case, the charging case can fully charge the earphones 1 to 2 times.
  • If the left LED light shows red and is ON (stays still without blinking) for 10 seconds, it means the charging case has 10% to 40% of battery, in this case, the charging case can fully charge the earphones for 0 to 1 time.
  • If the left LED light shows red and blinks for 10 seconds, it means the charging case has 0% to 10% of battery, in this case, the charging case is running out of battery and needs to be charged.

How to clean Tolv

Light-colored earphones always need to be treated with a bit of extra care.

For discolorations over time, we recommend to gently clean the areas with a damp cloth or with a small amount of water.

Tolv's charging case and earbuds are made of a special material, don't use alcohol to rub the charging case.

In some cases, being exposed to strong sunshine or high heat might alter the form of the silicon material.

Tolv - User Manual (PDF)

Tolv R

How to change songs on Tolv R

If you would like to go forward to the next song, quickly press the button on the right side twice. If you would like to go back to the previous song, quickly press the button on the left side twice.

Sometimes, with some apps, to go back to the previous song, you will need to do it on your phone device.

What to do when Tolv R is behaving unexpectedly or not pairing

If the earphones are behaving unexpectedly or you are having difficulty pairing, we recommend a reset. 

Please take your time with this process as there are several steps.

If the earphones fall out of sync, to pair again, you'll first have to bring them to the factory reset:

  1. Turn off both earphones by pressing and holding both buttons for 6 seconds.
  2. Start the earphones again by pressing and holding both sides for 13 seconds, until the lights stop blinking.
  3. Put the earphones back in the case and wait for 10 seconds.
  4. They are now reset.

Then you can start to pair them:

  1. Lift both earphones from the charging case at the same time (do not lift one by one, but both at the same time) and they will be in pairing mode.
  2. Select 'Sudio Tolv R' in the wireless connection list on your device.

How to check battery status on Tolv R

There are two LED lights on the back of the charging case.

The left LED light indicates the battery level of the case. The right LED light indicates the battery level of the earphones.

When it shows red light on the charging case, the case needs to be charged. When the red light changes to white light the charging case is fully charged. 

Charging the earphones in the charging case:

  • If the left LED light shows white and is ON (stays still without blinking) for 10 seconds, it means the charging case has 70% to 100% of battery, in this case, the charging case can fully charge the earphones 3 to 4 times.
  • If the left LED light shows white and blinks for 10 seconds, it means the charging case has 40% to 70% of battery, in this case, the charging case can fully charge the earphones 1 to 2 times.
  • If the left LED light shows red and is ON (stays still without blinking) for 10 seconds, it means the charging case has 10% to 40% of battery, in this case, the charging case can fully charge the earphones for 0 to 1 time.
  • If the left LED light shows red and blinks for 10 seconds, it means the charging case has 0% to 10% of battery, in this case, the charging case is running out of battery and needs to be charged.

Tolv R - User Manual (PDF)

Elva

How to pair Elva with a device

Please follow the instructions below to turn on your Sudio Elva and pair it with your device.

  1. Turn on the wireless connection in your device's settings. If it's already on, be sure to "refresh" by turning the connection off and on again.
  2. Press the middle button for 5 seconds. After you hear ‘power on’, continue holding the middle button until you hear a beep and ‘pairing’. Your Sudio Elva will then enter pairing mode.
  3. Locate and click on ‘Sudio Elva’ in your device's wireless connection list.
  4. Now your Sudio Elva is paired with your device.

How to turn off Elva

Press and hold the middle button around 5 seconds until you hear 'power off'.

How to use Elva with Siri or Google assistant

Hold the middle button for 1 second to active Siri or Google assistant.

How to change volume on Elva

If you would like to increase volume, press the button on the charging port side once and repeat it until you reach your preferred volume.
If you would like to reduce volume, press the button on the other side once and repeat it until you reach your preferred volume. 

elva-changevolume.png

How to change songs with Elva

If you would like to listen to the next song, press and hold the button on the charging port side for 2 seconds.
If you would like to go back forward to listen to the previous song, press and hold the button on the other side for 2 seconds.

elva-changesongs.png

 

How to take phone calls with Elva

When you take an incoming phone call or hang up the call, press the middle button once.
If you would like to refuse an incoming phone call, press and hold the middle button for 2 seconds.

Vasa Blå

How to change songs with Vasa Blå

Click and hold the button labeled (+) on the remote or headphone for 2 seconds to go to the next song.

Click and hold the button labeled (-) on the remote or headphone for 2 seconds to go to the last song.

 

How to use Vasa Blå with Siri or Google assistant

Press the middle and upper buttons (VOLUME +) simultaneously.

To deactivate the voice assistant, press the two buttons simultaneously again.

How to pair Vasa Blå with a device

  1. Turn on the wireless connection in your device's settings. If it's already on, be sure to "refresh" by turning the connection off and on again.
  2. Hold the middle button of the earphones for 5-8 seconds. The first blue flash means that your earphones are now turned on. Keep pressing the button until you see the red flash - this means the earphones are now ready to pair with your device.
  3. In the wireless connection settings, click on "Sudio Vasa Blå" to connect.
  4. Once connected, the earphones will flash blue every 8 seconds or so.
  5. You can now use your earphones!
  6. To turn off your earphones, hold the middle button for 7 seconds or so. It will flash blue, this means the earphones are turned off. 
 

How to check battery status on Vasa Blå

Battery life status will be indicated on your smartphone for iOS and most Android devices.

Due to different phone manufacturers have various Android versions, you can also download various battery apps on the Google Play Store.

A flashing red light indicates that the battery is low.

 

What to do if Vasa Blå is not charging

If the red light fails to shine when attached to your charger, then there is a chance there could be a battery issue within your earphones, your charging cord, or your charging port.

Problem testing:

  1. Make sure you are using the charging cable included with Vasa Blå.
  2. Make sure the cable is fully inserted into the earphones and that there is no dust or dirt blocking the port.
  3. Try to get power from a different source i.e. laptop USB port or from a wall outlet.
  4. Try using a different micro USB cable if you have one accessible.

The battery meter on your phone reads in increments of 20%. So it will go from 100, 80, 60, etc.

Vasa Blå - User Manual (PDF)

Tre/Tretton

How to change songs with Tre/Tretton

Click and hold the button labeled (+) on the remote or headphone for 2 seconds to go to the next song.

Click and hold the button labeled (-) on the remote or headphone for 2 seconds to go to the last song.

How to use Tre/Tretton with Siri or Google assistant

Press the middle and upper buttons (VOLUME +) simultaneously.

To deactivate the voice assistant, press the two buttons simultaneously again.

How to pair Tre/Tretton with a device

  1. Turn on the wireless connection in your device's settings. If it's already on, be sure to "refresh" by turning the connection off and on again.
  2. Hold the middle button of the earphones for 5-8 seconds. The first blue flash means that your earphones are now turned on. Keep pressing the button until you see the red flash - this means the earphones are now ready to pair with your device.
  3. In the wireless connection settings, click on "Sudio Tre/Sudio Tretton" to connect.
  4. Once connected, the earphones will flash blue every 8 seconds or so.
  5. You can now use your earphones!
  6. To turn off your earphones, hold the middle button for 7 seconds or so. It will flash blue, this means the earphones are turned off. 

How to check battery status on Tre/Tretton

Battery life status will be indicated on your smartphone for iOS and most Android devices.

Due to different phone manufacturers have various Android versions, you can also download various battery apps on the Google Play Store.

A flashing red light indicates that the battery is low.

What to do if Tre/Tretton is not charging

If the red light fails to shine when attached to your charger, then there is a chance there could be a battery issue within your earphones, your charging cord, or your charging port.

Problem testing:

  1. Make sure you are using the charging cable included with Tre/Tretton.
  2. Make sure the cable is fully inserted into the earphones and that there is no dust or dirt blocking the port.
  3. Try to get power from a different source i.e. laptop USB port or from a wall outlet.
  4. Try using a different micro USB cable if you have one accessible.

The battery meter on your phone reads in increments of 20%. So it will go from 100, 80, 60, etc.

Tretton - User Manual (PDF)

Tio

How to change songs with Tio

Click and hold the button labeled (+) on the remote or headphone for 2 seconds to go to the next song.

Click and hold the button labeled (-) on the remote or headphone for 2 seconds to go to the last song.

How to use Tio with Siri or Google assistant

Press the middle and upper buttons (VOLUME +) simultaneously.

To deactivate the voice assistant, press the two buttons simultaneously again.

How to pair Tio with a device

  1. Turn on the wireless connection in your device's settings. If it's already on, be sure to "refresh" by turning the connection off and on again.
  2. Hold the middle button of the earphones for 5-8 seconds. The first blue flash means that your earphones are now turned on. Keep pressing the button until you see the red flash - this means the earphones are now ready to pair with your device.
  3. In the wireless connection settings, click on "Sudio Tio" to connect.
  4. Once connected, the earphones will flash blue every 8 seconds or so.
  5. You can now use your earphones!
  6. To turn off your earphones, hold the middle button for 7 seconds or so. It will flash blue, this means the earphones are turned off. 

How to check battery status on Tio

Battery life status will be indicated on your smartphone for iOS and most Android devices.

Due to different phone manufacturers have various Android versions, you can also download various battery apps on the Google Play Store.

A flashing red light indicates that the battery is low.

What to do if Tio is not charging

If the red light fails to shine when attached to your charger, then there is a chance there could be a battery issue within your earphones, your charging cord, or your charging port.

Problem testing:

  1. Make sure you are using the charging cable included with Tio.
  2. Make sure the cable is fully inserted into the earphones and that there is no dust or dirt blocking the port.
  3. Try to get power from a different source i.e. laptop USB port or from a wall outlet.
  4. Try using a different micro USB cable if you have one accessible.

The battery meter on your phone reads in increments of 20%. So it will go from 100, 80, 60, etc.

Tio - User Manual (PDF)

Femtio

How to turn Femtio on/off

Press and hold the power button for 2 seconds to turn on/off your Femtio.

How to change songs with Femtio

If you would like to jump forward to the next song, please press and hold the ‘+’ button for 2 seconds.

If you would like to go back forward to the previous song, please press and hold the ‘-’ button for 2 seconds.

 

How to take phone calls with Femtio

You can answer the incoming call using either your phone or Femtio. To answer the phone call using Femtio, press the pause/play button of the speaker once. You can end the phone call by doing the same. To block the phone call, press the pause/play button for 2 seconds.

If you want to switch the audio from your phone to the speaker and vice versa, press and hold the pause/play button for 2 seconds while answering the call.

How to use Femtio with Siri or Google assistant

You can activate voice assistants such as Siri and Google Assistant by pressing and holding the pause/play button for 2 seconds.

How to pair Femtio with a device

  1. Turn on your wireless connection in your device's settings. If it's already on, be sure to "refresh" by turning the connection off and on again.
  2. Turn on your Femtio by holding the power button for 2 seconds. Femtio will automatically be in pairing mode and the light on the far right will start quickly flash white.
  3. Click “Sudio Femtio” in your device list to connect.
  4. Once connected, the light will flash white every 3 seconds. You can now use your Femtio.

What to do when Femtio is behaving unexpectedly or not pairing

If your speaker is behaving unexpectedly or you are having difficulty pairing, we recommend you do a factory reset.

Before you start, please check the serial number of your product which can be found on the back of the product packaging, and typically near a barcode. Serial numbers are a unique sequence of numbers that are around 11-digit long. After checking your serial number, please follow the steps corresponding to your model.

If your serial number starts with 31 or 503, follow this factory reset
1. Go into the wireless connection settings and “forget” Femtio on all connected devices. Femtio will no longer be synced.
2. Turn off the speaker.
3. Press and hold the power button for 10 seconds.
4. Femtio is now reset. Turn it on to pair your device by following the “How to pair Femtio with a device” step. 

If your serial number starts with other numbers, follow this factory reset
1. Press the leftmost button and minus button together for 3 seconds.
2. Femtio is now reset. Turn it on to pair your device by following the "How to pair Femtio with a device" step. 

Regent/Regent II

Regent - User Manual (PDF)
How to pair Regent/Regent II with a device

  1. Turn on your wireless connection in your device's settings. If it's already on, be sure to "refresh" by turning the connection off and on again.
  2. Hold the middle button of the earphones for 5-8 seconds. The first blue flash means that your earphones are now turned on. Keep pressing the button until you see the red flash - this means the earphones are now ready to pair with your device.
  3. In your wireless connection settings, you will see "Sudio Regent" listed - click connect.
  4. Once connected, the earphones will flash blue every 8 seconds or so.
  5. You can now use your earphones!
  6. To turn off your earphones, hold the middle button for 3 seconds or so. It will flash red, this means the earphones are now turned off.

How to change songs with Regent/Regent II

Click and hold the button labeled (+) on the remote or headphone for 2 seconds to go to the next song.

Click and hold the button labeled (-) on the remote or headphone for 2 seconds to go to the last song.

 

How to use Regent/Regent II with Siri

Siri needs to be activated on your device first. You can give the command "Hey Siri" through the earphone's microphone once Siri is activated.

How to check battery status on Regent/Regent II

Battery life status will be indicated on your smartphone for iOS and most Android devices.

Due to different phone manufacturers have various Android versions, you can also download various battery apps on the Google Play Store.

A flashing red light indicates that your battery is low.

 

Klar

How to use Klar with Siri

Siri needs to be activated on your device first. You can give the command "Hey Siri" through the earphone's microphone once Siri is activated.

How to pair Klar with a device

  1. Turn on your wireless connection in your device's settings. If it's already on, be sure to "refresh" by turning the connection off and on again.
  2. Hold the middle button of the earphones for 5-8 seconds. The first blue flash means that your earphones are now turned on. Keep pressing the button until you see the red flash - this means the earphones are now ready to pair with your device.
  3. In your wireless connection settings, you will see "Sudio Klar" listed - click connect.
  4. Once connected, the earphones will flash blue every 8 seconds or so.
  5. You can now use your earphones!
  6. To turn off your earphones, hold the middle button for 3 seconds or so. It will flash red, this means the earphones are now turned off.

How to change songs with Klar

Click and hold the button labeled (+) on the remote or headphone for 2 seconds to go to the next song.

Click and hold the button labeled (-) on the remote or headphone for 2 seconds to go to the last song.

How to check battery status on Klar

Battery life status will be indicated on your smartphone for iOS and most Android devices.

Due to different phone manufacturers have various Android versions, you can also download various battery apps on the Google Play Store.

A flashing red light indicates that your battery is low.

Klar - User Manual (PDF)

Flyg

What is Sudio Flyg?

Sudio Flyg is a wireless connection adapter that allows you to connect Sudio Elva with analog audio devices.

It contains a transmitter that can turn any audio signal from a device with a 3.5mm headphone jack or double 3.5mm flight audio socket into a wireless signal.

Sudio Flyg lets you enjoy a seamless listening experience with devices such as portable gaming devices, in-flight entertainment and television screens.

Sudio Flyg is included with Sudio Elva, but it can also be connected to other Sudio products with wireless connection functionality and earphones made by other companies. The connection method with Sudio Flyg is the same as when connecting Sudio Elva.

How to turn Flyg on/off

Press and hold the button for approximately 5 seconds until the LED shows a steady light.

It will turn off automatically after some time if nothing is transmitted or the earphone is not paired.

How to plug in Flyg

Flyg has two jacks, which can be used separately or together.

Devices without a wireless connection function that have a 3.5 mm headphone jack including portable gaming devices and televisions can be turned into wireless products by simply plugging Sudio Flyg into a headphone jack.

You can also connect it to in-flight entertainment, where two-pin socket is required most of the time. When there is only one output available, please use the main pin. 

flyg-mainpin.png

How to use Flyg with Elva

First, you need to pair your Sudio Elva with Sudio Flyg. Once they are paired, you are ready to connect Sudio Flyg to any audio devices.

Please follow the instructions below:

  1. Make sure there are no other wireless connection-activated devices around you to prevent Sudio Flyg from connecting to the wrong devices.
  2. Press and hold the round button on your Sudio Flyg for 5 seconds until the LED light starts blinking white.
    flyg-pairwithelva.png
  3. Turn on your Sudio Elva and enter pairing mode by pressing the middle button for 7 seconds.
  4. Keep your Sudio Elva very close (1 to 2 cm) to Flyg.
  5. Once you see the LED light on your Sudio Flyg stop blinking, your Sudio Elva is successfully paired to Sudio Flyg.
  6. Plug Sudio Flyg into the device to which you want to connect Sudio Elva. If there is only one output available, use the main pin.
  7. Now your device and Sudio Elva are successfully connected.
 

What to do when Flyg is behaving unexpectedly or not pairing

If your Sudio Flyg is behaving unexpectedly or you have problem connecting your earbud to Sudio Flyg, we recommend a factory reset to delete all settings and pairing data.

To reset the connection to your Sudio Flyg, please quickly click the button on your Sudio Flyg 3 times.

How to check battery status on Flyg

Please press the button on your Sudio Flyg once to see the current battery status.

  • 50% - 100% battery: The light is off.
  • 10% - 50% battery: The light blinks red and white.
  • Less than 10% battery : The light remains red.

Powered by Zendesk